@ORIC Manufactory       marketing@oricsystems.com/marketing@oricdigital.com
You are here: Home » DTF Power
6
5
4
2
1
DTF Hot Melt Powder
Special for DTF Printing

Classification

Soft DTF Powder, Rough DTF Powder, Anti-stretch DTF Powder, Anti-sublimation DTF powder, Breathable DTF powder

Feature

DTF powders are specially designed for use with DTF printing. The powder comes in 1 kg, 5 kg, 20 kg, and 25 kg. Packaging is divided into bags and barrels.

The feel of clothes depends on the type of powder you are using and the thickness of your ink layer. Our soft and stretchy DTF powder has a better hand than traditional vinyl or other types of heat transfer. It’s elastic and soft to the touch.

Our DTF powders are slow-drying and easy to cold-tear. This revolutionary technology will help you get excellent transfer printing results.
 
  • Technical Specifications

Size: 30cm/60cm/120cm*100m, A3, A4
Both sides mattee coating
Smooth and clean surface
90μm thickness
Applicable ink: pigment ink
Scratch resistant, non-fading, washable
Non-slip, no oil, no sticking, no static, uniform coating, easy to peel

Digital heat transfer film is divided into :
 single side
 double sides,
 performance as hot film,
 performance aswarm film
 performance ascold film.

For hot film, the appearance of the pattern and the cloth pattern are more natural when tear film off immediately after printed.
For cold film, the appearance of the pattern is relatively smooth, but the sense of paint and leather is aggravated when tear film off after temperature down.
  • Powder Classification:

There are coarse 80 mesh, middle 120 mesh, fine 200 mesh, we can match the specific application according to customer requirements

 Washing marks with small words can match fine powder and hot film.

 Large area pattern can choose warm and cold film and coarse powder.

 For the general pattern, hot melt glue powder recommended to 
   choose medium - fine powder.

 Normally, hot melt powder should be sealed, in order to avoid affecting 
    the use effect of shaking powder.

 Due to the difference of printer, ink, ICC curve of board and substrate fabric of each user,        we can develop a perfect heat transfer film plans according to our own condition.

 If the film surface absorbs moisture or dust caused by long-term exposure, the exposed           section should be cut off and then printed again, in order to avoid affecting our judgment.
     Handle the film gently, avoid compression and contusion, pay attention to the strength 
     and Angle when cutting the film, in order to avoid making deep scratches.
 
 Superior Soft Hand Feel       Great Wash Resistance       Stretchability
Classification Feature
Soft DTF Powder Particle size 80-170um, easy to melt, soft and smooth after the transfer, suitable for smooth and flat fabrics, such as T-shirts, sweaters, sweaters, polo shirts
Rough DTF Powder Particle size: 120-250, easy to melt. After transferring, the hand feel is obvious. It is suitable for rough fabrics, such as denim, non-woven fabrics, and linen.
Anti-stretch DTF Powder This powder is very fine and easy to melt, the transfer finished product is stretch-resistant, and suitable for stretch fabric
Anti-sublimation DTF powder It is used to block clothing colors or patterns that may be visible through transfer. easy to melt, Suitable for dark fabrics
Breathable DTF powder Breathable DTF powder provides a more breathable print with a smooth feel and softness
Testing Condition:​​​​​​​
Transfer Temperature: 130-160℃ Transfer Time: 8-15 seconds​​​​​​​
About Environment:
In order to protect unused film, it is recommended to store it in its original packaging, in the poly bag, at 68°F–82°F (20°C–28°C) and 40–60% RH.
About Storage:
​​​​​​​
Keep away from moisture, seal the bag in time after opening .​​​​​​​
About Printing:​​​​​​​
The paper is wound around the image side. Printing is performed in a "mirror" image. Allow the printing ink to dry before transferring.​​​​​​​

Method and Steps

 
1、The pattern to be applied through photoshop or other image processing software to complete the preprocessing, then input into the digital printing software.

2、The printer should make the best match between the consumables such as the 
matching hot transfer film, ink, and image color ICC and the software. The printed                  pattern is guaranteed to be bright and stable.
Printing humidity condition should remain 50%-60%;
 Indoor temperature should remain 20-30℃;
 The temperature of printer rear heating board should remain 38℃~45℃.

3、After printing the pattern, let the film flow into the automatic powder shaker machine.
Due to ink and other reasons, please pay attention to climate change, we can be turned      on the front and rear heating function to ensure stable quality during low temperature in          winter.Baking machine connected heating board is also recommended to 40-50 degrees.

4、Generally, the baking speed after shaking powder is appropriate to match the printing  
speed. The temperature is best to be warm first and then hot. It is appropriate to      
control the temperature of the film surface between 70 and 90℃.

5、After baking, the finished film with pattern should be printed on the surface of        
substrate clothing and other materials by heat transfer printing machine 
as early as possible.
 Heat printing temperature: 140-160℃, 
it can be adjusted by the physical properties of hot melt powder;
 Heat printing time: 7sec to 10se;
 Heat printing pressure: 5--7KG;
 According to the different fabric matching
  • Ink flow


    Reasons

    1、It becomes easy to flow ink where has powder impurities or crush wounds    2、The heating board is not open after printing 

    Solutions

    If the ink flow is due to the poor absorption, we can try 1, reduce the proportion of white ink setting, appropriate to reduce the amount of white ink 2, increase the temperature of the printer heating board can also improve the pass rate 3, board heating can help ink activation and then reduce ink flow phenomenon

  • Powder shaken unclear

    Reasons

    Wet weather, humidity, strong static electricity, it needs to check when the edge of the pattern is unclean.
    1、 Whether high humidity or low temperature                
    2、Whether the strength of powder shaking machine is insufficient              
    3、Whether the printing interval is too long without powder caused by drying glycerin diffusion                             
    4、 Whether ink misting on heads

    Solutions

    If it is found that the pressure wheel position or large blank area shaking is not clean, it should be electrostatic influence or powder damp or too fine, you can take measures as appropriate.                
    Generally, increasing the temperature of the heating board after printing and shake powder machine connected board can reduce the edge powder shaken unclear.

  • Powder holes

    Reasons

    Ink water and glycerin boiling evaporation with high temperature and short time baking dried, which pulls holes out of the coating and film

    Solutions

    It' better to give priority to medium and fine powder, a little coarse powder or even no coarse powder, it works best when baking dried in the low and high temperature section for a long time, it works best when baking dried in the low and high temperature section for a long time, it can be gradual to dry oil and water and melt glue thoroughly, but no violent reaction. The resulting film is flexible, elastic, smooth and dry. If the powder machine begins with a slightly poor conditions, it's necessary to make use of the function of preheating chopping board to heat and steam away some water in advance to reduce the burden, dry them then shake powder.

  • Oily or damp

    Reasons

    Baking dried patterns or pasted and transferred patterns become oily and damp

    Solutions

    It belongs to the phenomenon that the glue is not baked thoroughly, the water and glycerin in the ink cannot be thoroughly baked and then reversed. Generally speaking, single sheet operating version with 120 degrees low temperature for a long time through it best. As powder is limited by the length of the powder machine, so we can try to raise the connected board appropriate high temperature to make the water and glycerin evaporation in advance might also help
  • Flaking powder

    Reasons

    The blank place powder around the pattern sticks the coating after heat transfer printing

    Solutions

    May due to the heat transfer printing pressure is too high, which makes the film ink absorbing layer damage peeling or fabric surface size easy to stick the coating. Generally, as long as the temperature and pressing time can meet the requirements of sticking firmly, it can be easily solved when adjust the pressure as small as possible down

Features
  • DTF powder is specially used for DTF printing. Our powder has excellent adhesion, excellent washability, and can accurately adhere to ink rather than film.

  • This powder can be cured at 150C or 300F and pressed for 10-20 seconds. Press the completed transfer again for 10 seconds, and put a piece of parchment paper on it to get a better feel.

  • This powder can be cured in an oven using a hot air gun or under a hot press.

  • Process to using the powder:
  • 1. Place the transfer paper on a hot-pressed pillow or hot-pressed foam.
  • 2. Lower the top heating plate until it is about 1 cm away from the transfer.
  • 3. Solidify the powder at 160C for about 2 minutes or until melted. 

  • At first it will become sparkling. Then it will melt and form a flat surface.
Applications of 
DTF Printer
Commonly used products such as T-shirts, hats, backpacks, lanyards, shoes and more to create unique fashion pieces. It can also be used in denim clothes, non-woven bags, gift bags, pearl clothing, baseball caps, fabric gift boxes, etc. Make your travel outfit unique .
 T-shirt                                Denim/Jeans
 Canvas                             Hoodies
 Backpacks.                      Lanyards
 Shoes                               Gift Bags
 Baseball Caps                 Fabric Gift Boxes
 Sweaters and more......

DTF Accessories

DTF Accessories inculding DTF textile inks, DTF shaking powder and PET Film with high quality accessories for DTF printing with affortable price.
 
DTF PET Films
DTF film can be transferred on a wide range of fabrics. Capable of printing to shirts, sweaters, hoodies, pullovers, canvas, denim, and more! Our DTF films have excellent ink absorption for high-precision printing. Use our film you will achieve high-quality, breathable, and smooth prints.
DTF Textile Prinitng Ink
DTF textile printing ink is highly compatible with print Epson heads. You can directly print your designs on different textiles and fabrics using Direct to Film Ink technology.ORIC offers different colors of DTF inks such as W, Y, K, M, C, Or, Gr, and also fluorescence pink & fluorescence yellow.
DTF Hot Melt Powder
Unlike DTG technology, DTF requires no pre-treatment.The most important factor is DTF Powder. DTF powders are specially designed to use with DTF printing process. Our DTF powders are slow drying and easy to cold tear. Which will help you get excellent transfer printing results.
Additional Value
01
Year Warranty
Within 1 year from the date of purchase, if the machine has non-man-made damage, you can enjoy free warranty service.
02

Online Technical Support
The expert team will serve you online and solve any problems you encounter for free.
03
Inkjet Printer Starter Kit
Starter kit pack including complete set of test inks, commonly used replacement parts,and the user's guide, installation Video Instructions.
04
Dealer’s Team Training
Regularly provide our dealers , technical training of new models, application solutions training, sales guidance training.

ORIC factory is a digital inkjet printing equipment manufacturer and solution provider For UV(Roll-roll/Hybird/Flatbed)/ Sublimatoin / ECO Solvent / Solvent / DTF / UV DTF / Texture Painting
 
 
More printer OEM services
welcome to consult us .
PRODUCTS :

Sign up for our Letor newsletter

Home
Leave a Message
Copyright © 2023 ORIC Digtial Technology Co.,Ltd. All Right Reserved.